Preface
This wall mount bracket is exclusively designed to mount the network camera. Refer to the catalog or the installation guide of the camera for supported cameras.
• WV-Q158C: Clear dome cover
• WV-Q158S: Smoked dome cover (approx. 50 % of transmittance)
Precautions
• Do not hang down from this product or use this product as a pedestal. Failure to observe this may cause a drop resulting in accidents.
• Use only the specified camera. Failure to observe this may cause a fall of an inappropriate camera resulting in injury or accidents. Refer to the catalog or the installation guide of the camera for supported cameras.
• Avoid installing this bracket in the locations where salt damage occurs or corrosive gas is produced. Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera may occur.
• Refer installation work to the dealer. Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.
• Do not install this product in locations subject to vibration. Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents.
• Install this product in a location high enough to avoid people and objects from bumping the product. Failure to observe this may cause injury.
• The measures of protection against a fall of the camera shall be taken. Failure to observe this may cause a drop resulting in injury. Be sure to install this bracket-specific safety wire.
• The screws and bolts must be tightened to the specified torque. Failure to observe this may cause a drop resulting in injury or accidents.
• Periodic inspections shall be conducted. Rust on the metal parts or screws may cause a fall of the product resulting in injury. Consult the dealer for the inspections.
• Select an installation area that can support the total weight. Selecting an inappropriate installation surface may cause this product to fall down or topple over, resulting in injury or accidents. Installation work shall be started after sufficient reinforcement.
• Install this product on a wall according to the instructions. Failure to observe this may cause injury or injury or accidents.
• Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury.
Precaution
for installation In order to prevent injury, the product must be securely mounted to a wall according to Installation Guide. This product is designed to be used indoors. This product is not operable outdoors.
• Make sure that the installation area is strong enough to hold the total weight of the camera assembly (approx. 2.1 kg {4.63 lbs.}) before installation.
• The screws that secure the wall mount bracket on the wall are not supplied. Prepare the screws according to the material, structure, strength and other factors of the mounting area and the total weight of objects to be mounted. In this case, wood screws and nails should not be used. • Do not place this product in the following places.
• Locations where a chemical agent is used such as a swimming pool
• Locations subject to moisture or oil smoke such as a kitchen
• Locations that have a specific environment that is subject to an inflammable atmosphere or solvents
• Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated
• Locations near coasts directly subjected to sea breezes, or locations subject to corrosive gases such as from hot springs, volcanic regions, etc.
• Locations where the temperature is not within –10 °C - +50 °C {14 °F - 122 °F}.
• Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This product is not designed for on-vehicle use.)
• Locations where it may get wet from rain or water splash (including under the eaves, etc.)
• Locations subject to moisture or dust
• Locations subject to condensation as the result of severe changes in temperature (In case of installing the product in such locations, the dome cover may become foggy or condensation may be caused on the cover.)
• The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area. After tightening the screws or bolts, perform visual check to ensure tightening is enough and there is no backlash.
• The pull-out strength of the installation area shall be 196 N {44 lbf} or more per 1 screw.