Specifications
Dimensions: 120 mm (W) x 269 mm (H) x 220 mm (D) {4-23/32 inches (W) x 10-19/32 inches (H) x 8-21/32 inches (D)}
Mass: Approx. 1.9 kg {4.19 lbs} Finish: Aluminum die cast Heavy salt damage prevention coating Silver
metallic Others: Heavy salt damage prevention (ISO14993-compliant) Weight and dimensions indicated are approximate. Specifications are subject to change without notice.
Preface
This mount bracket is used for installing the color CCTV camera or network camera on a ceiling. Refer to the catalog or operating instructions of the camera for further information about the compatible models.
About the user manuals
Due to product improvements, the illustrations, etc., appearing in this document may differ somewhat from the actual product, but not to the extent to affect its usage.
Refer installation work to the dealer.
Installation work requires technique and experiences. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.
Avoid installing this bracket in the locations where corrosive gas is produced.
Otherwise, the mounting portions will deteriorate and accidents such as a fall of this product may occur.
The screws and bolts must be tightened to the specified torque.
Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents
Do not use this bracket except with suitable cameras
Failure to observe this may cause a drop resulting in injury
Select an installation area that can support the total weight.
Selecting an inappropriate installation surface may cause this product to fall down or topple over, resulting in injury or accidents. Installation work shall be started after sufficient reinforcement.
Do not rub the edges of metal parts with your hand.
Strong rubbing may cause injury.
Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents. Consult the dealer for the inspections.
The measures of protection against a fall of this product shall be taken.
Failure to observe this may cause a drop resulting in injury. Be sure to install the safety wire.
Do not install this product in locations subject to vibration.
Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents.
The installation should comply with local electrical code.
Before start the installation/connection, check and prepare the required devices and cables. Before starting the connection, turn the power of the devices including the camera and the PC off.
Refer installation work to the dealer. Failure to observe this may cause fire, electric shock, injury, or damage to the product. In order to prevent injury, the product must be securely mounted to a ceiling according to installation instruction.
Installation place
Salt damage prevention is applied to this product. However, it is not completely anti-corrosive. Therefore, consider a place for installation where direct splash of seawater can be avoided. Especially when installing this product in a seashore area or a place where a snow-melting agent is applied, and also where rainwater is avoided, it is recommended to regularly clean and rinse off salt with water. In case of installing this product in a seashore area, regularly check the status of equipment. (Replace the parts as required.)
Power supply
Use a power supply device equipped with the ON-OFF switch for servicing. When the power cord of the product is connected to the power supply device, the power will be supplied to the product. Make sure that the power cable is not connected to the main power supply.
Installation area for this product
Consult the dealer about the installation area to select a strong ceiling area.
• The screws that secure this product are not supplied. Considering the material and strength of the area where the product is to be installed, prepare the screws according to the total weight of the camera and peripheral environment. Use the corrosion-resistant screws, or apply caulking to the screws to be used for fixing the framework and the adapter box. Recommended screw: M10 x 4 pcs. Minimum pull-out strength (per 1 pc.): 1411 N {317 lbf}
• Do not mount the product on a plaster board or a wooden section because they are too weak. If the product is unavoidably mounted on such a section, the section shall be sufficiently reinforced.
Mounting method for this product
This product is designed to be used as a pendant mount camera. If the product is mounted on a desktop or at a slant, it may not work correctly and its lifetime may be shortened.
Protection from lightning
When cables are used outdoors, there is a chance that they may be affected by lightning. In this case, install a lightning arrester close to the camera to prevent it from being affected by lightning, and keep the length of the network cable between the lightning arrester and the camera as short as possible.
Do not place this product in the following places:
• Locations where a chemical agent is used such as a swimming pool
• Locations subject to moisture or oil smoke such as a kitchen
• Locations that have a specific environment that is subject to an inflammable atmosphere or solvents
• Locations where radiation, X-ray, intense radio wave, or strong magnetism is produced
• On the sea or locations where direct seawater splashes, and where corrosive gas may be produced
• Locations subject to sulfur gas, such as a hot spring area
• Locations where the temperature is not within the specified range (–50 °C to +55 °C {–58 °F to 131 °F})
• Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This product is not designed for onvehicle use.)
• Locations subject to sudden changes in temperature, such as near the outdoor unit of an air conditioner (In case of installing the product in such locations, the dome cover may become foggy or condensation may be caused on the cover.)
Screw tightening
• The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area.
• Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening excessively.
• When a screw is tightened, make the screw at a right angle to the surface. After tightening the screws or bolts, perform checks to ensure that the tightening is sufficient enough so that there is no movement or looseness.